Getting Familiar with Plumbing: Before Installing a Bathtub
Getting Familiar with Plumbing: Before Installing a Bathtub
Blog Article
This great article which follows relating to How to Install a Bathtub Yourself is quite enjoyable. Give it a go and make your own personal final thoughts.
Setting up a bathtub isn't precisely brain surgery, but it does require strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a new one is additionally a reasonably tough project. If the old tub is conveniently accessible, the task can move speedily; if you need to open up a wall surface to remove the old tub and position the brand-new tub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have actually qualified yourself for the job and also fit trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to think about employing one prior to you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your restroom if you have already bought a brand-new tub as well as do not require to alter the setup of your previous water supply pipes.
Your devices as well as product checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the faucet and the sink. Secure the tap in place with the producer supplied backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be connected to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Load the bath tub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the bathtub ought to wait until the tub has been made use of at the very least when as this will settle it right into its final position.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to fracture a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, bring about difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the motion experienced when the tub remains in use. The sealer can split fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that editorial on How to Install a Bathtub Yourself from a friend on another domain. Do you know another individual who is interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Take a moment to share it. Kudos for your time. Visit again soon.
Schedule Free Estimate Report this page